espanol english
twitter    facebook    google plus
agricultura almeria malaga acuicultura granada cadiz acuaponia cordoba jaen semilleros barcelona valencia invernaderos madrid bilbao cultivos e hidroponia zaragoza teruel floricultura donosti vitoria industria tarragona girona piscinas

Hydroponic System by computer

The pH and nutrient controller, Hydroponic System by computer is the most advanced automatic fertigation system on the market. With the software "by computer" we can control by computer, all water values, as well as the irrigation system.

It is able to apply various types of fertilizers and booster jointly, and in turn regulate the pH of the water in the tank.

The dosing flow of each of the regulators, with capacity from 0 to 7 L / h, is adjustable independently.

It automatically regulates the maximum-minimum level of water in the tank, as well as the temperature.

Activates the irrigation system of both the recirculation pump and the irrigation pump.

Functionalities: Hydroponics, aquaponics, seed beds, vertical gardens, backyard gardens, garden centres, aquariums, and grow shop. In any kind of installation where regulation of Ec and pH of the water is required.

Included in the box: The controller is delivered fully equipped and installed on a methacrylate panel, in which it is only necessary to connect the water inlet and outlet hose of the recirculation pump by means of simple quick connections.

It is fully equipped, including: Programming and communication manual, calibration envelopes pH7, pH4 and 1.430 ms / cm, supply and suction pipes, wall plugs and screws.

by computer or mobile device
Hydroponic System by Computer or mobile
garantia bomba de ec
All our products have a 2 year warranty against manufacturing defects, not for improper use in accordance with current regulations.

Operation of the Ec ProSystemAqua Hydroponic System by Computer .

  1. Ignition of Hydroponic System by computer

    Once the panel is installed and connected to power, we will proceed with programming:

    1. 1. Programming of the pH regulator:
    2. A- Establish the value that we want to obtain in the water.
    3. B- Set the working mode: pH down (acid) or pH Up mode (alkaline).
    4. C- Proceed to calibration.
    5. D- Adjust the proportional flow of the pH pump.
    6. E- Program maximum and minimum pH alarms.
    7. 2. Ec controller programming:
    8. A- Establish the value of Ec that we want to obtain in the water.
    9. B- Proceed to calibration.
    10. C- Adjust the proportional flow of the pumps of A, B and C.
    11. D- Program maximum and minimum alarms of Ec.
  2. Schedule irrigation times and work mode.

  3. Set the desired temperature in the water.

    A - Program maximum-minimum temperature alarm.
  4. Recirculation of water in the collector.

    The controller will activate the water recirculation pump and will recirculate the water through the collector where the pH, Ec and temperature probe are installed. In case of lack of water, the flow sensor alarm will be activated and will deactivate the controller to avoid overdosing.
  5. Conductivity measurement

    The Ec probe detects the conductivity in the water and is reflected on the controller's display.
  6. Aspiration and dosage of fertilizers

    The regulators for the control of the conductivity A, B and C aspirate through the filter of the cans of fertilizers and dosed through the injection valves of the water recirculation collector.
  7. PH measurement

    The pH probe continuously measures the value in the water that is indicated on the controller's display.
  8. Aspiration and dosage of the pH regulator

    The pH regulator aspirates from the bottle pH down or pH up and doses through the injector until it reaches the programmed value.
  9. Activation of the irrigation pump

    The irrigation pump will be activated by the controller once the pH and Ec values ​​are adjusted and stable.
  10. Level probes

    Level probes for automatic water filling in the tank.
  11. Filling Electro valve

    It will be activated by the controller through the level probes.
  12. Flow sensor

    Deactivates the controller in case of lack of water in the collector.
  13. Scaler

    The C regulator will begin dosing according to the configured pulses.
  14. Water heater

    It will be activated by the controller.
  15. Temperature sensor

    It measures the temperature of the water and activates the heater according to the temperature that we have programmed in the controller.
logo prosystemaqua
awared company
Prosystem Aqua Europe SL – Carretera del aeropuerto km. 5 – C.P. 14005(Spain) – Telf: +34 957 414 910 – email: